Nissan Titan Forum - View Profile: TitanZ04

TitanZ04 TitanZ04 is offline

Registered User

  Visitor Messages

Showing Visitor Messages 1 to 10 of 14
  1. Titangator
    05-19-2014 12:31 PM - permalink
    Hey how's it going. I tried to review our prior
    Discussion and I couldn't find it. Can u refresh
    My memory be cuz yes I need both sides. Not sure
    What u have or when we spoke.
  2. Titangator
    02-22-2014 04:57 AM - permalink
    Hey I'm interested in your manifolds if u still have them, mainly the drivers side for my 08.
  3. TitanZ04
  4. bigdeal
    11-25-2012 01:03 AM - permalink
    is it like a prg or what? just looking for the full name so i can research
  5. Ro_Ja Boy
    02-17-2010 03:13 PM - permalink
    Ro_Ja Boy
    Sounds good. not sure which im going with yet.
  6. TitanZ04
    07-28-2009 04:13 AM - permalink
    thanks. I don't think I like the blacked out look at this time. But, I would like to know where or Who did the powder coating?
  7. TitanOn40's
    07-28-2009 12:12 AM - permalink
    they are black powder
  8. TitanZ04
    05-02-2009 03:40 AM - permalink
    Great write-up. If pictures were included would make it excellentfor a Tech Manual insert...Thanks.
  9. HAYNBOI96743
    05-01-2009 12:10 AM - permalink
    It was pretty easy. I tried the 4 pin connector first and only the running lights and reverse lights came on. So I decided to hard wire and everything worked. You have to cut off the 4 pin plug that comes with the LED lightbar. Make sure you know what wire goes where. Take a picture of it if you have to, I did. The first wire on the left is your GROUND WIRE. Connect that to any part of the body that is metal and NOT PLASTIC. I just did mine to the bumper where the other wires are running by. Your 2nd wire is your brake lights. Just tap into your brake light wire from either your left tail light or right. You can use a splice tap or T connector. Removing the tail light would help with this installation if you don't know what wire is what. The remaining 3 wires will connect to the wires that are marked MAJOR. Just look on the tail light plug and it will tell you MAJOR, MINOR, and GROUND. Again tap into the one that says MAJOR. Your third wire is left turn signal and the 4th wire is your right turn signal. I ran mine from the middle so I had 3 wires going to the left tail light and the 4th wire going to the right tail light. Test all your lights to see that they work before you manage the cables with zip ties or what ever you want to use. You can use HEAT SHRINK to cover your connections and a silicone sealant to make it water tight. As for bar positioning removing the tailgate helps with placement and alignment. I used automotive grade velcro to secure my BAR and am very pleased. Better then the bars tape. Make sure to clean with alcohol first. This is for the PLASMAGLO 60" LED FLEXIBLE Light bar. I don't know how the other LED bars connect but I'm guessing that it would be the same. Good Luck!!!
  10. 1_fastsilverado
    04-26-2009 10:18 PM - permalink
    If you don't mind can you find a pic of what they look like, I've found a few styles of the 6 spoke ones and hate to make you open a box if they're ready to go. I was set on the 5 spokes but I have seen a few of the 6 spokes I like. Thanks.

  About Me

  • About TitanZ04
    04 TITAN LE 4x4 BT OR w/Navi,ABLS,E-Lock, & no VDC
    OEM Guard, Helix TBS, NISMO CAI, Stillen LT Headers w/ B & B Catback, Sway Bars, VK-Pro, ScanGaugeII


Total Posts
Visitor Messages
Total Thanks
General Information
  • Last Activity: Yesterday 10:10 PM
  • Join Date: 09-07-2005

  iTrader Score

iTrader Profile Recent Ratings
iTrader Score:
Positive Feedback:
Members who left positive:
Members who left negative:
Total positive feedback: 0
View Complete Feedbacks for TitanZ04
6 Months
12 Months
 Positive 0 0 0
 Neutral 0 0 0
 Negative 0 0 0