Go Rhino Dominator II Step Bars Installed w/PIX

AgTitan06 · 06-12-2007, 11:36 PM

Installed my new step rails tonight, and I couldn't wait until daylight to show you guys. Snapped a few dark pix of them to give you an idea. Yes, I know my truck needs a bath - she is getting one this weekend, don't worry. I'll take some better pictures of the rails tomorrow hopefully.

I like them because they look good, and aren't bulky like the OEM step rails. It still allows you to see how high the truck is!

By the way, I had to use a lantern to install the step rails, because it was pitch black...That's dedication right there!!!!

Here are the better pictures:

hooligan · 06-13-2007, 12:34 AM

is it me or am i looking at n-fab step bars? looks good anyhow, but they look like the n-fabs. how much?

AgTitan06 · 06-13-2007, 06:32 AM

Quote:

Originally Posted by hooligan

is it me or am i looking at n-fab step bars? looks good anyhow, but they look like the n-fabs. how much?

They are virtually identical to the N-FABs, except they are much better quality IMO. They are made of high-grade stainless steel and powdercoated black. The N-FABs have been known to rust out very quick. These won't rust. They are around $330

54warrior · 06-13-2007, 06:35 AM

Yeah, had I not purchased my N-Fabs long ago, I'd be going with a set of these. The step pad on the Go Rhino units are much nicer as well!!! Looks good Ag, Do they mount the same way as the N-Fabs do-utilizing the existing holes/studs on the body??

I will say that N-Fab was good about replacing my rusted ones though, and I now have two sets!!! I hope, should you have any warranty concerns, that GoRhino takes care of you as well. I've not heard much about them as a company.

jasonmotox · 06-13-2007, 06:52 AM

I was looking into the N-fabs myself, but if the Rino's cost less and are stainless steel powder coated, you've changed my mind.
How about a close up shot of the step?

**Kronos1965** · 06-13-2007, 07:14 AM

Quote:

Originally Posted by AgTitan06

They are virtually identical to the N-FABs, except they are much better quality IMO. They are made of high-grade stainless steel and powdercoated black. The N-FABs have been known to rust out very quick. These won't rust. They are around $330

Summitracing.com

Love my rhinos and if the black powdercoating chips, I'll get the whole think linux'd!

AgTitan06 · 06-13-2007, 07:49 AM

Quote:

Originally Posted by jasonmotox

I was looking into the N-fabs myself, but if the Rino's cost less and are stainless steel powder coated, you've changed my mind.
How about a close up shot of the step?

I'll have plenty of shots later once I can take pictures in the daylight.

AgTitan06 · 06-13-2007, 07:50 AM

Quote:

Originally Posted by 54warrior

Yeah, had I not purchased my N-Fabs long ago, I'd be going with a set of these. The step pad on the Go Rhino units are much nicer as well!!! Looks good Ag, Do they mount the same way as the N-Fabs do-utilizing the existing holes/studs on the body??

I will say that N-Fab was good about replacing my rusted ones though, and I now have two sets!!! I hope, should you have any warranty concerns, that GoRhino takes care of you as well. I've not heard much about them as a company.

Yes, the mount using the same 3 holes/studs that the OEM rails use.

jasonmotox · 06-13-2007, 08:01 AM

where'd you purchase them from? I checked Summit and couldnt locate any for the Titan.

AgTitan06 · 06-13-2007, 08:10 AM

Quote:

Originally Posted by jasonmotox

where'd you purchase them from? I checked Summit and couldnt locate any for the Titan.

I got them from Socal Motorsports, where I am a sales rep. They're not listed on the website though. We ordered them from one of our distributors.

54warrior · 06-13-2007, 08:22 AM

Quote:

Originally Posted by AgTitan06

Yes, the mount using the same 3 holes/studs that the OEM rails use.

Another plus for the GoRhino's. The N-Fabs only use the front and rear mount holes, a total of four per side, where as yours have six per side. Definitely a MUCH better deal for the GoRhino's.

Pictures of the front/rear of the steps would be nice too--are they capped off in some fashion, or just a hollow tube at the ends??

AgTitan06 · 06-13-2007, 08:28 AM

Quote:

Originally Posted by 54warrior

Another plus for the GoRhino's. The N-Fabs only use the front and rear mount holes, a total of four per side, where as yours have six per side. Definitely a MUCH better deal for the GoRhino's.

Pictures of the front/rear of the steps would be nice too--are they capped off in some fashion, or just a hollow tube at the ends??

They are capped off.

**P's Titan** · 06-13-2007, 08:30 AM

those are some nice Red X's ( damn work blocks PB and others )

congrats Erik

AgTitan06 · 06-13-2007, 09:02 AM

Quote:

Originally Posted by P's Titan

those are some nice Red X's ( damn work blocks PB and others )

congrats Erik

Anyone know a better picture hoster that isn't blocked by most works?

I just love tinypic because it's so easy to upload..no registration or anything.

AgTitan06 · 06-13-2007, 09:04 AM

Quote:

Originally Posted by P's Titan

those are some nice Red X's ( damn work blocks PB and others )

congrats Erik

Thanks