Nissan Titan Forum banner

1 - 10 of 10 Posts

·
Registered
Joined
·
107 Posts
Discussion Starter · #1 ·
So I ordered the Rancho lift yesterday and 4wheel parts called back and said it would be weeks untill it would be shipped. I talked them into a procomp stage 1 lift with 5125 Bilstein rears and 5100 fronts for an amazing deal. I was 99% sure this will work fine I just want to be 110%. quick feed back would be appreciated, with the settings on 0 how much will this actually lift? :redblob"
 

·
Registered
Joined
·
792 Posts
The 5100's at the 0 setting I believe lift the front 1/2". You shouldn't have a problem with them at all, just make sure they install all of the washers in the correct order or it can get pretty ugly. Other than that the lift is a great lift. One of the most popular lifts on here.
 

·
Registered
Joined
·
107 Posts
Discussion Starter · #3 ·
great thank you for your response. I know I will have to do a little banging around/filling on the rear shocks to get them to fit. I also have 17x8.5 with 0 offset rims and 295 70 r17 terra grapplers coming in. Picked up everything for around 3.1K I think I got a good deal.

On another note any Idea about which pinion angle shim I should get? I belive it comes with 3" rear blocks?
 

·
Registered
Joined
·
6,061 Posts
great thank you for your response. I know I will have to do a little banging around/filling on the rear shocks to get them to fit. I also have 17x8.5 with 0 offset rims and 295 70 r17 terra grapplers coming in. Picked up everything for around 3.1K I think I got a good deal.

On another note any Idea about which pinion angle shim I should get? I belive it comes with 3" rear blocks?

The Pro Comp blocks are tapered. You shouldn't need a shim.

I am, however, running a 1* shim on the rear of mine in combination with a PRG Drive Shaft Spacer.
 

·
Banned
Joined
·
3,888 Posts
how much for the pro comp lift?
 

·
Registered
Joined
·
107 Posts
Discussion Starter · #6 ·
well i had ordered the rancho with 9000xl and they wernt going to have it for weeks so i got the bilsteins an pc lift for 1800.
Everything is in except the rear shocks. i have time and a place to do the lift this weekend, would it be ok if i instaled it with the stock rear shocks for a few days untill i get the 5125s? I know it would probably make the rear ride terrible
 

·
Registered
Joined
·
792 Posts
The stock shocks will not stretch enough to fit. You can ride around for a few days with no shocks at all, it is just going to be a little bouncy. Nothin out of control, just takes the rear end a little bit longer to settle down. how long are you expecting to wait on the bilsteins?
 

·
Registered
Joined
·
107 Posts
Discussion Starter · #8 ·
im guessing early next week
 

·
Banned
Joined
·
3,888 Posts
1800 is a decent deal. cost on that lift is about 1200
 

·
Registered
Joined
·
31 Posts
sorry to bring back an old thread, but to the original poster i have a question for you? im seeing you ordered the procomp stage 1 kit? did you NEED to order the bilsteins for the front, or did you just order them for a "better" ride. im asking because i was told when you order the procomp stage 1 kit it comes with everyting you need to lift the front, ie es series procomp struts, huge spacer etc. etc.

can you verify this for me? im really wanting to order my lift, but noone including 4wheelonline can give me a direct answer..


thanks.
mike
 
1 - 10 of 10 Posts
Top