Nissan Titan Forum banner

Power Door Lock and Keyless Entry Install Questions??

10209 Views 2 Replies 3 Participants Last post by  nyc07_king.titan
Hey I am trying to install Power Door locks (MES) and a Keyless Entry Alarm (Hornet from A1) and Im having a couple problems.....

Can anyone explain where to get the ACC 12v and the Constent 12v Power from? I am trying to get it off the radio harness and it does not seem to work right because the door locks only work when the key is on ACC and the alarm light only flashes when the key is on ACC.

Is this a power problem or somthing else?

Im also having an issues with the keyless entry setup working with the door locks, I cant get them to do anything!

If anyone has some input please let me know!

Thanks, Eric :rockon
1 - 3 of 3 Posts
get all your power at the ignition switch.



MODEL YEAR(S)
TITAN 2004 -2006
KEY T-HARNESS IMMOBILIZER
N/A N/A NISSAN'S TRANSPONDER ANTI-THEFT SYSTEM, Requires 791 Bypass Module and extra Ignition Key
PART COLOR LOCATION
12 VOLT CONSTANT GREEN (+) IGNITION SWITCH HARNESS
STARTER BROWN (+) See NOTE *1 IGNITION SWITCH HARNESS
STARTER 2 LIGHT GREEN (+) or BLUE/GREEN (+) See NOTE *1 IGNITION SWITCH HARNESS
IGNITION 1 BLACK/RED (+) IGNITION SWITCH HARNESS
IGNITION 2 N/A
IGNITION 3 N/A
ACCESSORY/HEATER BLOWER 1 RED (+) IGNITION SWITCH HARNESS
ACCESSORY/HEATER BLOWER 2 PURPLE (+) IGNITION SWITCH HARNESS
KEYSENSE N/A
PARKING LIGHTS ( - ) N/A
PARKING LIGHTS ( + ) RED/BLUE (+) @ DIMMER SWITCH ON DASH
POWER LOCK BLUE (TYPE B) @ MODULE, INSIDE DRIVERS DOOR
POWER UNLOCK RED (TYPE B) (Requires Double Pulse) @ MODULE, INSIDE DRIVERS DOOR
DOOR TRIGGER See NOTE *2 @ BCM, See NOTE *3
DOMELIGHT SUPERVISION BLUE (-) @ BCM, PIN 63, See NOTE *3
TRUNK RELEASE N/A
SLIDING POWER DOOR N/A
HORN RED/WHITE (-) @ STEERING COLUMN HARNESS
TACH ANY WIRE NOT WHITE/BLUE or BLACK @ ANY IGNITION COIL
WAIT TO START LIGHT N/A
BRAKE RED/GREEN (+) or RED/BLACK (+) @ SWITCH ABOVE BRAKE PEDAL
FACTORY ALARM DISARM DISARMS WITH UNLOCK, Single Pulse Disarms
ANTI-THEFT TRANSPONDER ANTI-THEFT SYSTEM, REQUIRES 791 BYPASS MODULE AND EXTRA IGNITION KEY TRANSPONDER @ IGNITION SWITCH TUMBLER
EXTRA INFORMATION
NOTE *1 When Installing a REMOTE STARTER, you MUST use BOTH Starter #1 and Starter #2 wires. Both wires must be connected to the STARTER/CRANKING Output wire from the Remote Starter or the vehcile will NOT Remote Start when the Engine is cold. NOTE *2 THE LEFT FRONT DOOR TRIGGER IS LIGHT BLUE(-) IN PIN 47. THE RIGHT FRONT DOOR TRIGGER IS RED/BLUE(-) IN PIN 12. THE LEFT REAR DOOR TRIGGER IS RED/YELLOW(-) IN PIN 48. THE RIGHT REAR DOOR TRIGGER IS RED/WHITE OR GRAY(-) IN PIN 13. WHEN CONNECTING TO AN ALARM SYSTEM USE ALL 3 DOOR TRIGGER WIRES AND DIODE ISOLATE, TO CONNECT, See DIAGRAM NOTE *3 the BCM (Body Control Module) is located to RIGHT of the STERERING COLUMN
See less See more
i got the power for my alarm and power door locks from under the dash. theres a topic on here some where that i used that had pics and all. dont use a1 power door lock kit. get the oem door locks from a se or le titan from courtsey nissan and your be happy you did. the cable splice is not worth the trouble.
1 - 3 of 3 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top