GW77 Airaid MXP CAI Ram-Air Mod.

TA CC TX · Feb 24, 2013

I was impressed with the diff between the ***** and MXP easy install and solid attaches with oem rubber grommets. DO IT! haha ( glad I still had my old oem box) cuban post 114

Cuban11182 · Feb 24, 2013

I just did too!!! Last one

Thanks Thor. Just ordered one. I hate AT&T DSL. I'm using my smart phone to tether my laptop to my it. 4G is faster than it. Pretty pathetic.

tsunamilogan05 · Feb 24, 2013

Mine will be here Friday from Amazon. Purchased this previous Friday.

tsunamilogan05 · Feb 24, 2013

Finished my ram air today. Took me only two 4" 45° elbows. Both female/male ends. For some reason I didn't have as much room as Chris lol. Even between cutting the entrance hole. Oh well got it to fit.
Also found some kind of draft foam that I can paint and sand when it dries. Used it cover around the entrance next to my headlight.

Looks like my ram air has rabies. I'll post a pic later when it's sanded, tapered, and painted.

gweasel77 · Feb 25, 2013

Nice work, tsunamilogan!!! :coolsmile

For some reason I didn't have as much room as Chris lol.

I did have the front end re-built after i was in an accident a couple years back. Could possibly be because of that? :teethmast

gweasel77 · Feb 25, 2013

Looks like my ram air has rabies. I'll post a pic later when it's sanded, tapered, and painted.

LOL! I know it always looks funny until you get it sanded down & painted.

gweasel77 · Feb 25, 2013

What i did as an added safety feature to go along with the Airaid Pre-Filter was to leave the bottom bolt & rubber grommet out completely. This way when your driving through heavy rain you don't ever have to worry about water collecting in your air box! Since its the lowest point in the air box any water that enters through the ram-air tube or the oem fender air inlet will run down into the deep corner & drain right out!

Water drain hole!

HAHA

All i did was use a couple pieces of foam with adhesive on the back to put under the box to support it without the bottom bolt.

Its still a super snug fit & doesn't make rattle or anything!

LVTAP · Feb 27, 2013

Nice job with the ram air!

Atlas09 · Apr 15, 2013

Got it done today. I think the size of the volant caused me to make some changes. I had to cut down the last 45. And I couldnt find a 4" intake coupler but I used a decent amount of clear silicone to seal everything. Obviously not as good if I need to remove it and put it back. I did get a good seal though going towards the radiator, really forcing the air forwards the 4" pipe. Thanks for all the info guys. Hopefully I did it well enough to feel and see some gains.

Sent from my Autoguide iPhone app

tsunamilogan05 · Apr 15, 2013

Atlas09 said:
Got it done today. I think the size of the volant caused me to make some changes. I had to cut down the last 45. And I couldnt find a 4" intake coupler but I used a decent amount of clear silicone to seal everything. Obviously not as good if I need to remove it and put it back. I did get a good seal though going towards the radiator, really forcing the air forwards the 4" pipe. Thanks for all the info guys. Hopefully I did it well enough to feel and see some gains.

Sent from my Autoguide iPhone app

How come you didn't get the volant ram air attachment? Or are you running it too lol

Sent from AutoGuide.com App

Atlas09 · Apr 15, 2013

tsunamilogan05 said:
How come you didn't get the volant ram air attachment? Or are you running it too lol

Sent from AutoGuide.com App

Because I'm 4x4.

Sent from my Autoguide iPhone app

titanss · Apr 15, 2013

The Volant RA tube is not worth the money, the way it is done now, will see bigger gains.

Atlas09 · Apr 15, 2013

Should the hole for the bottom scoop be sealed? I know it was proven to leave the side fender opening open would allow better airflow. I wonder if the filter on the volant will be as good as the MXP filter for the ram air. Being that it's designed to pull from the fender.

Sent from my Autoguide iPhone app

MikeClark · Oct 6, 2015

I did my ram air a while back. I also found an 8$ spray gun bottle to use as my windshield washer reservoir! I threaded an npt fitting to the spray gun bottle and ran a piece of rubber hose to the fluid pump. I just don't have the fluid guage hooked up. This setup is good for 2-4 windshield washes lol but its better than nothing. I also have a cap to put over the pipe going into the air box for the rainy days . Enjoy!

[/URL][/IMG]

GW77 Airaid MXP CAI Ram-Air Mod.

TA CC TX

Cuban11182

tsunamilogan05

tsunamilogan05

gweasel77

gweasel77

gweasel77

LVTAP

Atlas09

Attachments

tsunamilogan05

Atlas09

titanss

Atlas09

MikeClark

Top Contributors this Month

Recommended Communities