Nissan Titan Forum banner
Cancel
Create thread New Garage Forums

Aftermarket Y-pipe setups, post pics please!

Jump to Latest
1 - 20 of 45 Posts
J

JauntyBishop

· Premium Member
Joined
·
4,945 Posts
Discussion starter · #1 ·
Hey yall,

I would like to see some aftermarket B-pipe to Y-pipe Setups, or really any under carriage exhaust shot to the aftermarket Y-pipe you guys have.

Preferably the Flowmaster Y-pipe and Magnaflow Y-pipe, or if your're baller, a Burns Stainless design.

Thanks!
 
Discussion starter · #2 ·
Btw, i just wanted you all to know as of 4:51 am in florida time, the first 14 threads after the last "sticky'' i am the last poster lol... i was thinking of doing the whole page, but you guys would probably freak out...

saying like "this Milenkogt is F'n google searching info sourcing non sleepin thread postin fool...son"...lol.
 
#3 ·
Here's my magnaflow DI 2.25"/SO 2.5" ypipe. I don't like the location of the ypipe but it works for now. The guy said that it was the only way he could make it work.



Sent from my iPhone using Autoguide
 

Attachments

  • Like
Reactions: JauntyBishop and gweasel77
Save
Reply Quote Like Like
#4 ·
I just found these couple photos of the y-pipe I built. I couldn't find any photo's of the finished product off the truck. It's 2.5, merging at 10 degrees, into 3 inch oval to 3 inch round. It goes into a 3 inch bullet muffler then dumps before the rear axle, but just yesterday, finally tired of the drone, I installed a dynomax vt muffler and am waiting for some bends to come in to do a side exit before the rear tire. I'll try to find some more photos, or climb under and take one if you want.

Image
Image


Image
Image
 

Attachments

#5 ·
#8 ·
Ohhh now you make a thread...

I just posted all my pics in the other thread.

Hold on i'll get them. :bangit: LOL

................................................

This is from the initial install:
Image

Image

I think the guy could have done a better job, but it was CHEAP! ;)

Just took these. Its getting kinda dark outside not the best lighting. Its been storming all week:
Image

Image

The straight piece of 3" pipe after the Y-Pipe is the only piece left of my Banks Catback for now.
I sold the 3" Y-Pipe, but i still have the over the axle tailpipe section & 5" tip! ;)

Image

Image

Image

Image

Sounds even better than it sounded with the Banks Muffler!

I pretty much want to have it completely redone from the B-Pipe flanges to the Y-Pipe.

No crush bends, just smooth transitions all the way back! :eyebrow:
 
  • Like
Reactions: yamahatitan, JauntyBishop and WIKEDVK
Save
Reply Quote Like Like
Discussion starter · #10 ·
Nice setups guys! I really need to get some better 90deg bends after the B-pipes going into my Y...

Is there a way to not have a huge bend on passender side after leaving B-pipe going into the Y-pipe? Mine has it, which is similar to Gweasels.

However, most of you guys 90deg bends coming from the drivers side are a lot better than mine lol. I just need a welder and some time...
 
#11 ·
I'll get pics up later sometime. I have stock pipes:( to flow master y directly to the banks.
 
#12 ·
#13 ·
nightowl said:
HMMMMMM!! What size pipe is that on the catback? Arnt you the fastest Titan on the forum? Just wondering...lol :)
Click to expand...
LOL....2.5 from the headers to the Y pipe into 3 in tail pipe....I'm one of the fastest on motor behind toomanymods 12.92 titanss 13.18 and me 13.36....but that will be changing before years end
 
#14 ·
firelife25 said:
LOL....2.5 from the headers to the Y pipe into 3 in tail pipe....I'm one of the fastest on motor behind toomanymods 12.92 titanss 13.18 and me 13.36....but that will be changing before years end
Click to expand...
He stole this set up from me :smileysqu click the link in my sig and you can see my set up, i just need some headers and i'll be running firelife's times :coolsmile :rofl:
 
#15 ·
reds_titan said:
He stole this set up from me :smileysqu click the link in my sig and you can see my set up, i just need some headers and i'll be running firelife's times :coolsmile :rofl:
Click to expand...
haha.....dammit dont give my secrets away.....
 
#16 ·
firelife25 said:
haha.....dammit dont give my secrets away.....
Click to expand...
it's ok i stole it from DeerSlayer... :rofl: Maybe hit your times if i had that new GTM set up :coolsmile
 
#17 ·
firelife25 said:
LOL....2.5 from the headers to the Y pipe into 3 in tail pipe....I'm one of the fastest on motor behind toomanymods 12.92 titanss 13.18 and me 13.36....but that will be changing before years end
Click to expand...
Coming after you myself!!:bump: Just need to rid myself of the stock manifolds and cats. Some traction help and weight reduction would also be nice.
 
Save
Reply Quote Like Like
#18 ·
06HemiRam said:
Coming after you myself!!:bump: Just need to rid myself of the stock manifolds and cats. Some traction help and weight reduction would also be nice.
Click to expand...
Good luck!!!
 
#20 ·
I know you mentioned it already, but you should really look into getting your Y relocated as far forward as possible when you get a chance.

Like this:
Image
 
  • Like
Reactions: WIKEDVK
Save
Reply Quote Like Like
1 - 20 of 45 Posts
About this Discussion
44 Replies
15 Participants
Last post:
Nightmarevk56
Nissan Titan Forum
posts
4M
members
177K
Since
2003
Nissan Titan Talk Forum is a community for truck owners to discuss the Titan Cummins, Warrior, Midnight Edition and more!
Full Forum Listing
Explore Our Forums
Titan General Discussion Member Classifieds Titan Performance Modifications Titan Suspension Titan Parts & Accessories